Water level Alarm Circuit

 Here is a simple water level alarm circuit that will produce an audible alarm when the water level reaches  a preset level.The circuit can be powered of a  3V battery and is very handy to use.

The circuit is based on an astable multivibrator wired around IC1 (NE 555).The operating frequency of the astable multivibrator here will depend on capacitor C1, resistances R1,R2 and the resistance across the probes A&B.When there is no water up to the probes,they will be open and so the multivibrator will not produce oscillations and the buzzer will not beep.When there is water up to the level of probes,some current will pass through the water,the circuit will be closed to some extend,and the IC will start producing oscillations in a frequency  proportional to the value of C1,R1,R2 and the resistance of water across the probes.The buzzer will beep to indicate the presence of water up to the level of the sensing probes.source circuitstoday.com

Stereo Decoder Circuits

Dingdong Sound Generator

This is the circuit diagram of a ding dong sound generator based on two NE555 timer ICs.The circuit is designed to toggle between two adjustable frequencies to produce the ding dong sound. The first NE555 (IC1) is wires as an astable multivibrator operating at 1Hz. The frequency of the second NE555 (IC2) is modulated by the output from the first IC. MORE...>

Power Supply 120 MA

12V/120mA switch mode power supply circuit.Transformer less switch mode power supplies have become very popular these days. The circuit shown below is of a 12V/120mA output, 85 to 230V AC input transformerless switch mode power supply using LNK304 IC. Applications of a power supply based on this IC includes hand held devices, timers, small appliances, LED drivers, industrial gadgets etc.LNK304 is a low component count, efficient off-line switcher IC that can support buck, buck-boost and flyback topologies. MORE...>

 

Stereo Decoder Circuit

In FM stereo transmission left and right channels are algebraically encoded into sum (left + right) and difference (left-right) signals. This is done in order to make the mono FM receivers compatible with the stereo transmission. The mono receiver will reproduce the summed left and right channel and the listener will hear both these channels through a single loud speaker. Stereo decoder is a circuit which is used in stereo FM receivers in order to recover the left and right channel information from the composite transmission signal. This task is achieved by adding the difference signal to the summed signal to recover left channel and subtracting the difference signal from the summed signal to recover the right channel. MORE...>

Stereo Decoder Circuit

In FM stereo transmission left and right channels are algebraically encoded into sum (left + right) and difference (left-right) signals. This is done in order to make the mono FM receivers compatible with the stereo transmission. The mono receiver will reproduce the summed left and right channel and the listener will hear both these channels through a single loud speaker. Stereo decoder is a circuit which is used in stereo FM receivers in order to recover the left and right channel information from the composite transmission signal. This task is achieved by adding the difference signal to the summed signal to recover left channel and subtracting the difference signal from the summed signal to recover the right channel.

The circuit diagram of a stereo decoder using MC1310P IC from Motorola is shown below. MC1310P is an integrated stereo decoder IC chip which is available in 14 pin DIL plastic package.
Circuit description.
In the circuit composite signal if fed to the input pin (pin2) of the IC through decoupling capacitor C12. Capacitors C6 and C7 do the job of power supply filtering. Capacitor C3 plus Resistors R3 and R4 forms the RC for the ICs internal oscillator circuit. Resistor R2 plus capacitors C1 and C2 forms a loop filter. D1 is an indicator LED and R1 limits the current through it. The decoded left and right stereo outputs are available at pins 4 and 5 respectively. C10 and C11 are the DC decoupling capacitors for the left and right outputs.

source : circuitstoday.com

Temperatur Control DC Fan

Here is a simple circuit based on two transistors that can be used to control the speed of a 12 V DC fan depending on the temperature.A thermistor (R1) is used to sense the temperature. When the temperature increases the base current of Q1 (BC 547) increases which in turn decreases the collector voltage of the same transistor. Since the collector of Q1 is coupled to the base of Q2 (BD 140), the decrease in collector voltage of Q1 forward biases the Q2 more and so do the speed of the motor. Also, the brightness of the LED will be proportional to the speed of the motor.

Circuit diagram with Parts list.

Notes.
The R1 can be a 15K @ 20°C ,N.T.C  thermistor.
The M1 can be a 12V,700mA fan motor.
The capacitor C1 must be rated 25V.
The circuit can be powered from a 12V PP3 battery or 12V DC power supply.
Assemble the circuit on a good quality PCB or common board.

source: circuitstoday.com

Power Supply 10 MA - 12 volt

12V/120mA switch mode power supply circuit.

Transformer less switch mode power supplies have become very popular these days. The circuit shown below is of a 12V/120mA output, 85 to 230V AC input transformerless switch mode power supply using LNK304 IC. Applications of a power supply based on this IC includes hand held devices, timers, small appliances, LED drivers, industrial gadgets etc.LNK304 is a low component count, efficient off-line switcher IC that can support buck, buck-boost and flyback topologies. The IC has a built in auto start circuit for short circuit and open loop fault protection. Other features of LNK304 includes low temperature variation, thermal shut down,high break down voltage, good line & load regulation, high band width , wide input voltage range (85 to 230V AC) etc. In general the LNK304 has a better performance when compared to the many other discrete buck regulators.LNK304 pin configuration and typical application
The pin configuration and the typical application diagram of LNK304 are shown above. Drain (D) pin the drain connection of the built in power MOSFET. The external by pass capacitor (0.1uF) is connected to the BYPASS (BP) terminal. FEEDBACK (FB) pin controls the switching of the built in power MOSFET. A current above than 49uA delivered to this pin will inhibit the switching. The internal power MOSFETs source is connected to the SOURCE (S) pin.
12V /120 switch mode power supply circuitThe circuit diagram of a practical 12V/120mA transformerless switch mode power supply is shown above.
Resistor R1, capacitors C1 and C2, diodes D1 and D2 and inductor L1 forms the input stage. D1 and D2 forms the rectifier section while C1 and C2 are input filters. Resistor R1 which is a fusible resistor limits the inrush current, increases differential mode noise attenuation and also serves as an input safetyfuse.The next stage is the regulator stage which consists of IC LNK304, diodes D3 and D4, capacitorsC3, C4 and C5, resistors R3, R4 and R5 and inductor L2. D3 is the freewheeling diode while L2 isthe output choke. C5 is the output filter capacitor which limits the output ripple voltage to a value as low as possible. The IC LNK304 is so configured that the power supply operated in the most discontinuous mode and that’s why a fast recovery diode (UF4005) is used as the freewheeling diode (D3). UF4005 has a reverse recovery time of around 75nS and it is well enough for the given situation.The voltage drop across diodes D3 and D4 are practically same and so the voltage across C4 tracks the output voltage and this voltage is picked by the network comprising of resistors R2, R3 and is fed to the feedback pin. R2 and R3 sets the output voltage and for 12V output the voltage at the feedback pin must be 1.65V DC. The circuit attains regulation by skipping the switching cycles. When the output voltage rise, the current at the feedback pin also rises and when the current rises above the threshold value, subsequent cycles are skipped until the current at the feedback pin goes below the
threshold and thus a constant output voltage is maintained.The IC will auto restart if no cycles are skipped during a 50mS time period and this limits the maximum output power to 6% of the maximum over load power. That’s how over load protection is attained. Resistor R4 serves as a small preload which nullifies the effects of tracking error.
source: http://www.circuitstoday.com

Dingdong Sound Generator

This is the circuit diagram of a ding dong sound generator based on two NE555 timer ICs.The circuitis designed to toggle between two adjustable frequencies to produce the ding dong sound. The firstNE555 (IC1) is wires as an astable multivibrator operating at 1Hz. The frequency of the second NE555(IC2) is modulated by the output from the first IC. This is attained by connecting the output of first IC to the control pin (pin5) of the second IC. The tone of the sound depends on the frequency of the second IC and the changeover time depends on the frequency of the first IC.

Notes.

The circuit can be assembled on a Vero board.

Use 9V PP3 battery for powering the circuit.

POT R4 can be used to adjust the tone of the sound.

POT R2 can be used to adjust the change over time.

IC1 and IC2 must be mounted on holders.

K1 can be a 8 ohms, 1/2 watt tweeter.

source:http://www.circuitstoday.com

Zero Crossing Detektor

Zero-crossing detector is an applied form of comparator. Either of the op-amp basic comparator

circuits discussed can be employed as the zero-crossing detector provided the reference voltage Vref

is made zero. Zero-crossing detector using inverting op-amp comparator is depicted in figure. The

output voltage waveform shown in figure indicates when and in what direction an input signal vin

crosses zero volt. In some applications the input signal may be low frequency one (i.e. input may be

a slowly changing waveform). In such a case output voltage vOUT may not switch quickly from one

saturation state to the other. Because of the noise at the input terminals of the op-amp, there may

be fluctuation in output voltage between two saturation states (+ Vsat and – Vsat voltages). Thus

zero crossings may be detected for noise voltages as well as input signal vin. Both of these problems

can be overcome, if we use regenerative or positive feeding causing the output voltage vout to change

faster and eliminating the false output transitions that may be caused due to noise at the input of

the op-amp.

source:http://www.circuitstoday.com

MNC TV
TV UNO

Astro Tv online

Rangkaian Lampu Berdenyut

Konverter Dc 12-24 volt

The circuit diagram of a very simple voltage doubler using NE555 timer is shown here. Here IC NE555 is wired as an astable mutivibrator operating at around 9KHz. The base of the two transistors (Q1 and Q2) is shorted and output of the astable multivibrator (pin 3) is connected to it. When the output of astable multivibrator is low, Q1 will be OFF and Q2 will be ON. The negative terminal of the capacitor C3 will be shorted to ground through T2 and it will be charged to the input supply voltage. When the output of the astable multi vibrator is high, transistor Q1 will be ON and transistor Q2 will be OFF. The capacitor C4 will be charged to the voltage across capacitor C3 plus the input supply voltage (that is double the input voltage). This is how the circuit works.
This voltage doubler circuit can deliver only up to 50mA output current and above that current limit the output voltage will be dramatically reduced. The actual output voltage will be around 19V for a 12V DC input and also the output voltage will be a bit unstable. Anyway, for low current applications this circuit is well enough.

source: http://www.circuitstoday.com

Battere Eliminator Circuit

Here is the circuit diagram of a battery eliminator circuit that can be used as a
replacement for 9V PP3 batteries. The circuit given here can be used to power any device
that operates from a 9V battery. The transformer T1 steps down the mains voltage and
bridge D1 performs the job of rectification. Capacitor C1 is a filter. IC LM317T is the
regulator here. The value of R1, R2 and R3 are so selected that the output voltage of
IC1 will be steady 9 volts.
Notes.
Assemble the circuit on a good quality PCB.
Transformer T1 can be a 230V primary, 9V secondary, 1.5A step down transformer.
If 1A Bridge is not available, then make one using four 1N 4007 diodes.
Do not connect loads that consume more than 1.5A to this circuit.
A heat sink is recommended for IC1.

source: http://www.circuitstoday.com

Convert Cdroom to Audio cd player

    Here is the simplest scheme for converting a CD ROM drive of your computer to a Audio CD
player.The minimum requirement for the player is that, it should have a audio output and
skip button. Luckily most of the Cd ROM’s are equipped with both of these.
The CD ROM drive needs two voltages ,12V & 5V for its operation.So the main objective is
to build a suitable power supply for the CD ROM drive.The IC1 (7812) together with
associated components produce a regulated 12V DC.The IC2 (7805) together with associated
components produce a regulated 5V DC.These voltages as well as ground can be connected
to the corresponding voltage pins of the CD ROM drive using a male type CD ROM drive
power connector.The 12V can be connected to the yellow wire of connector, 5V to red wire
and GND to black wire as shown in figure1.Now the power supply is ready.
Make the circuit as shown in the circuit diagram.Power up the circuit after connecting
the power connector to the CD ROM drive. Now the power LED of the drive will glow.Insert
the audio CD.Now the music will be available at the audio output socket of the drive.It
can be heared using a headphone.The skip button of the drive can be used to play next song.
By connecting the audio output to a power amplifier you can enjoy the music in a greater
wattage.Click Here! to get the amplifier circuits suitable for this project.
Notes.
For car stereo applications you don’t need the transformer,rectifier and the 7812
regulator.12V will be available from battery.You just need to produce a 5V from it using
a 7805 based regulator. Connect the corresponding voltages to the connector as shown in
figure 1 and connect the connector to drive.Done.
The amplifier for the car audio CD player must be one operating from 12V.
Do not connect the voltages to CD ROM drive in wrong polarity.Double check the voltages
using a multimeter. Wrong polarity could easily damage the drive.

source:www.circuitstoday.com

Speaker to Microphone Converter Circuit

  This circuit is a simple approach for converting a loud speaker into a microphone. When
the sound waves fall on the diaphragm of a speaker, there will be fluctuations in the
coil and there will be a small proportional induced voltage. Usually this induced
voltage is very low in magnitude and useless. Here in the circuit the low voltage is
amplified using transistors to produce a reasonable output. The transistor Q1 is wired
in common base mode and produces the required voltage gain. The transistor Q2 is wired
as an emitter follower to produce enough current gain. The voice quality of this circuit
will not be as much as a conventional microphone but quite reasonable quality can be
obtained. To set up the circuit, keep the preset R2 at around 10 Ohms and connect the
battery. Now adjust R2 to obtain the optimum sound quality.
Notes.
Assemble the circuit on a general purpose PCB.
Power the circuit from a 9 V PP3 battery.
A 3 inch speaker can be used as K1.
All capacitors must be rated at least 15V.
An 8 Ohm speaker or head phone can be connected at the output to hear the picked sound

source: http://www.circuitstoday.com

Light to Frequency Converter Circuit

    Here is the circuit diagram of a effective light to frequency converter circuit that can
be used for variety of applications such as light intensity measurement,fun etc.
The circuit is based on TLC555, the CMOS version of famous timer IC NE 555. A photo
diode is used for sensing the light intensity.The timer IC is wired in astable mode.The
leakage current of the reverse biased photo diode is proportional to the light intensity
falling on it.This leakage current charges the capacitance C1.When the capacitor voltage
reaches 2/3 of the supply voltage the out put (pin 3) goes low.As a result the capacitor
discharges through photo diode .When the capacitor voltage reaches 1/3 the supply
voltage the out put (pin 3) of IC goes high.This cycling continues and we get a
frequency at pin 3  proportional to the light intensity falling on the photo diode.
Notes.
With the given components the frequency  varies from 1KHZ @ complete darkness to  24 Khz
@  bright sunlight.The frequency range can be changed by using different values for C1.
Use any general purpose photo diode for D1

source: http://www.circuitstoday.com

Digital To Analog Konverter

 A D/A Converter is used when the binary output from a digital system is to be converted into its equivalent analog voltage or current.The binary output will be a sequence of 1's and 0's. Thus they ma be difficult to follow. But, a D/A converter help the user to interpret easily.Basically, a D/A converter have an op-amp. It can be classified into 2 types. They are
1. Digital to Analog Converter using Binary-Weighted ResistorsA D/A converter using binary-weighted resistors is shown in the figure below. In the circuit, the op-amp is connected in the inverting mode. The op-amp can also be connected in the non-inverting mode. The circuit diagram represents a 4-digit converter. Thus, the number of binary inputs is four.Digital-to-Analog Converter Circuit - Binary-Weighted Resistors MethodWe know that, a 4-bit converter will have 24 = 16 combinations of output. Thus, a corresponding 16 outputs of analog will also be present for the binary inputs.Four switches from b0 to b3 are available to simulate the binary inputs: in practice, a 4-bit binary counter such as a 7493 can also be used.
Working
The circuit is basically working as a current to voltage converter.b0 is closedIt will be connected directly  to the +5V.Thus, voltage across R = 5V
Current through R = 5V/10kohm = 0.5mA
Current through feedback resistor, Rf = 0.5mA (Since, Input bias current, IB is negligible)
Thus, output voltage = -(1kohm)*(0.5mA) = -0.5V
b1 is closed, b0 is open
R/2 will be connected to the positive supply of the +5V.
Current through R will become twice the value of current (1mA) to flow through Rf.
Thus, output voltage also doubles.
b0 and b1 are closed
Current through Rf = 1.5mA
Output voltage = -(1kohm)*(1.5mA) = -1.5V
Thus, according to the position (ON/OFF) of the switches (bo-b3), the corresponding “binary-weighted” currents will be obtained in the input resistor. The current through Rf will be the sum of these currents. This overall current is then converted to its proportional output voltage. Naturally, the output will be maximum if the switches (b0-b3) are closedV0 = -Rf *([b0/R][b1/(R/2)][b2/(R/4)][b3/(R/8)]) – where each of the inputs b3, b2, b1, and b0 may either be HIGH (+5V) or LOW (0V).The graph with the analog outputs versus possible combinations of inputs is shown below.Digital-to-Analog Converter Circuit - Binary-Weighted Resistors Method GraphThe output is a negative going staircase waveform with 15 steps of -).5V each. In practice, due to the variations in the logic HIGH voltage levels, all the steps will not have the same size. The value of the feedback resistor Rf changes the size of the steps. Thus, a desired size for a step can be obtained by connecting the appropriate feedback resistor. The only condition to look out for is that the maximum output voltage should not exceed the saturation levels of the op-amp. Metal-film resistors are more preferred for obtaining accurate outputs.DisadvantagesIf the number of inputs (>4) or combinations (>16) is more, the binary-weighted resistors may not be readily available. This is why; R and 2R method is more preferred as it requires only two sets of precision resistance values.
2. Digital to Analog Converter with R and 2R Resistors
A D/A converter with R and 2R resistors is shown in the figure below. As in the binary-weighted resistors method, the binary inputs are simulated by the switches (b0-b3), and the output is proportional to the binary inputs. Binary inputs can be either in the HIGH (+5V) or LOW (0V) state. Let b3 be the most significant bit and thus is connected to the +5V and all the other switchs are connected to the ground.

source: http://www.circuitstoday.com

Switching Regulator 3A

 

When compared to linear voltage regulators the switching voltage regulators are much
power efficient. In the case of linear voltage regulators the difference between the
input and output voltage is just wasted and for switching regulators there is almost no
such wastage and that’s why the switching regulators have great power efficiency ranging
up to 85% . In simple words, the switching regulator operates by taking small bits of
energy from the input voltage source and then transferring it to the output with the
help of a solid state switch and a control circuitry. Since the switching element is
either fully open or closed at any moment, no energy is wasted  across it. The control
circuit controls  the duty cycle of the solid state switch which in turn determines rate
at which energy is transferred to the output.
The electronic circuit given here is of a simple and low cost switching regulator using
the IC LM317 that can deliver up to 3A of current. The input voltage range of this
circuit is between 8 to 35V DC and the output voltage can be adjusted between 1.8 to 32V
DC. The output voltage can be adjusted by using the POT R
Notes.
Assemble the circuit on a good quality PCB.
C4 and C3  must be a solid tantalum capacitor.
Transistor T1 and IC1 require heat sinks.
L1 can be a 600uH inductor.

source: http://www.circuitstoday.com

20 Watt Amplifier & Voltage Level Detektor

This is just another 20W audio amplifier circuit , but this time based on the LM1875 audio amplifier IC from National Semiconductors. With a 25V dual power supply LM1875 can deliver 20W of audio power into a 4 ohm speaker. The LM1875 requires very less external components and has very low distortion. The IC is also packed with a lot good features like fast slew rate, wide supply voltage range, high output current, high output voltage swing, thermal protection etc. The IC is available in TO-220 plastic power package and is well suitable for a variety of applications like audio systems, servo amplifiers, home theatre systems etc.source :circuitstoday.com.

The circuit as explained by Rakesh:

The design came from the interest of finding a new technique of analog to digital conversion. The two types of ADC (Analog to Digital Converter) that inspired me in the development of this circuit are Flash Type ADC and Successive Approximation Type ADC.  The Flash Type ADC is the fastest ADC available in the market (highest sampling rate 120 Msps) but it uses a huge number of OP-AMPS. On the other hand Successive Approximation Type ADC uses fewer components but its speed is dependent upon the clock frequency provided to it. I was looking for a technique that can give a trade-off between this two, the result of which is this circuit.
Construction
The working of this circuit is similar to that of decimal fraction to binary fraction conversion. For this purpose, the circuit amplifies a signal and compares it to a reference voltage. The circuit can be divided into a number of stages. Number of stages can be increased or decreased according to need. Each stage contains two OP-AMPs(TL084).  One of them (OP-AMP at the left side) is used for comparison purpose. The other (OP-AMP at the right side) is used as a non-inverting amplifier with a fixed gain (EXACTLY 2). The input voltage is connected to the non-inverting pin/terminal of each OP-AMP. The digital output is obtained from the output of the comparing OP-AMP and the output of the amplifier OP-AMP is fed to the input of the next stage. To obtain a reference voltage, two resistors are used.
Working
An input voltage is applied. The OP-AMP used as a comparator compares the input voltage with the reference level. If it exceeds a certain reference level, the comparator output goes high and there is amplification along with subtraction operation is performed by the amplifying OP-AMP. If the input voltage is less than the reference voltage, only the amplification operation is performed. The output of the amplifier OP-AMP is inherited to lower stages.
The output of my interest is the outputs obtained from the comparator OP-AMPs. They together represent binary number.source :circuitstoday.com

Crossover Active Circuit

Crossover circuits are of two types, active and passive. Passive crossover circuit uses passive components only and they are very simple, but they waste a considerable amount of energy and also induce distortion. Active crossovers does not have the above said draw backs and they are a better option for HiFi audio systems. Active crossovers split the incoming complex audio signal into to two bands, a low frequency out and a high frequency out. These two bands a separately amplified by two power amplifier stages, one tuned to the low frequency band and the other tuned to high frequency stage respectively (bi-amping).
The cross over circuit given here uses LM833 National Semiconductors. LM833 is a dual operational amplifier especially designed for audio applications. The circuit requires four opamps and so two LM833 ICs are used here. The circuit can be divided into two parts, a high pass filter section and a low pass filter section. IC2b forms a first order Butterworth low pass filter circuitry and the low frequency out is available at its output pin (pin1). The high frequency out is available at pin 7 of IC1a. For the given components crossover frequency is 1KHz and it is according to the equation Fc = 1/(2pRC).

source: http://www.circuitstoday.com

Ni-MH battery charger

This is the circuit diagram of a very powerful and efficient Ni-MH battery charger using IC LT4060 from Linear Technologies. In addition to Ni-MH batteries Ni-Cd batteries can be also charged by slightly modifying the circuit.For charging Ni-Cd batteries connect the CHEM pin (pin12) of the IC to +Vcc.Here the circuit is configured to charge 2 cells connected in series. By altering the connections of SEL0 and SEL1 pins, upto 4 batteries in series can be charged using this circuit. For charging a  single cell, connect SEL0 and SEL1 pins to GND. For charging two cells, connect SEL1 to GND and SEL0 to Vcc. For charging  three cells,  connect SEL1 to VCC and SEL0 to GND. For charging 4 cells, connect SEL0 and SEL1 pins to VCC. The circuit also features temperature based charge qualification.An NTC thermistor connected at the NTC pin (pin11) of the IC serves as the temperature sensor.

source: http://www.circuitstoday.com

Tachometer Circuit

ENGLISH  and  INDONESIAN
>< Here is a simple circuit that can be used as a tachometer. The circuit is basically a frequency to current converter which converts the incoming signal into a proportional current to drive the meter. The deflection on the ammeter will be proportional to the frequency of the incoming signal. For using this circuit as an automobile tachometer, the input terminal A should be connected to the spark plug cable and terminal B should be connected to the vehicles ground.
For calibrating the circuit, set R2 at 25K and R4 at 5K.Power up the circuit and feed the input terminal with a 60Hz square wave form your function generator. Adjust R2 so that the meter shows 0.36 mA (equal to 3600rpm). Now disconnect the input signal and adjust R3 so that the meter shows 0mA.Now connect the 60Hz signal again and if the meter does not show 0.36mA adjust R4.A completely calibrated circuit will show 0mA at 0Hz and 0.36mA at 60Hz.

>< Berikut adalah rangkaian sederhana yang dapat digunakan sebagai sebuah tachometer. Rangkaian ini pada dasarnya frekuensi untuk konverter arus yang mengubah sinyal yang masuk ke arus proporsional untuk mendorong meter. Defleksi pada ammeter akan sebanding dengan frekuensi dari sinyal yang masuk. Untuk menggunakan rangkaian ini sebagai tachometer mobil, terminal masukan A harus dihubungkan ke kabel busi dan terminal B harus terhubung ke tanah kendaraan.Untuk mengkalibrasi rangkaian, set R2 pada 25K dan R4 pada 5K.Power atas sirkuit dan pakan terminal input dengan bentuk gelombang persegi 60Hz fungsi generator Anda. Sesuaikan R2 sehingga meter menunjukkan 0,36 mA (sama dengan 3600rpm). Sekarang lepaskan sinyal input dan menyesuaikan R3 sehingga meter menunjukkan 0mA.Now menghubungkan sinyal 60Hz lagi dan jika meter tidak menunjukkan 0.36mA menyesuaikan sirkuit R4.A sepenuhnya dikalibrasi akan menunjukkan 0mA di 0Hz dan 0.36mA pada 60Hz.

source: http://www.circuitstoday.com

Update Terbaru

This circuit can be used to test whether mains voltage is present or not without having electric contact with mains line. The CMOS IC CD4033 is the heart of this circuit. The CD4033 consists of a 5 stage decade Johnson counter and an output decoder for converting the Johnson code to a 7 segment decoded output for driving 7 segment LED display.READ MORE...

Power saving LED lamp from your scrap box.
This circuit is designed by Mr Seetharaman Subramanian and we are very glad to publish it here. In this article he is showing a method to convert a broken/defunct CFL into a LED based power saving light.READ MORE...
 Here is a very useful lamp flasher circuit using the famous adjustable voltage regulator IC LM317T. LM317 can source up to 1A of current and so up to 12W lamps can be used with this flasher. Such a circuit finds huge application in automobiles.READ MORE...

This is a simple and easy to construct digital dice circuit. The circuit is based on a single IC, CD4060B.The dice consists of six LEDs marked D1 to D6.The number of LEDs glowing indicates the numeral.READ MORE...

Here is a simple dancing light circuit based on NE555 (IC1) & CD4017 (IC2) .The IC1 is wired as an astable multivibrator to provide the clock pulses for the CD4017.

READ MORE...